Influences of chip serration on micro-topography of machined surface in high-speed cutting

Saw-tooth chip changes from macroscopically continuous ribbon to separated segments with the increase of cutting speed. The aim of this study is to find the correlations between chip morphology and machined surface micro-topography at different chip serration stages encountered in high speed cutting. High strength alloy steel AerMet100 was employed in orthogonal cutting experiments to obtain chips at different serration stages and corresponding machined surfaces. The chips and machined surfaces obtained were then examined with optical microscope (OM), scanning electron microscope (SEM), and white light interferometer (WLI). The result shows that chip serration causes micro-waves on machined surface, which increases machined surface roughness. However, wave amplitudes (surface roughness) at different serration stages are different. The principal factor influencing wave amplitude is the thickness of the sawed segment (tooth) of saw-tooth chip. With cutting parameters in this study, surface roughness contributed by chip serration ranges from 0.39 μm to 1.85 μm. This may bring on serious problems in the case of trying to replace grinding with high-speed cutting in rough machining. Some suggestions have been proposed to control the chip serration-caused surface roughness in high-speed cutting based on the results of the current study.     

Thermo-physical properties of as deposited and aged thermal barrier coatings (TBC) for gas turbines: State-of-the art and advanced TBCs

In the perspective of fuelling the future generations of gas turbines by hydrogen rich syngas, the evaluation of the effect of a higher water vapour content into the flue gases on the TBC used, or potentially usable, is a need. For this purpose YPSZ APS TBC with two different microstructures have been exposed for 500?h at different temperatures in the range 1000?°C–1250?°C either in air and air +20% vol. H₂O. The comparison between the different testing conditions has been performed in terms of sintering kinetics and phase stability, as evaluated by thermal diffusivity measurements and Synchrotron X-Rays diffraction, respectively. Furthermore the characterisation of thermal properties of two innovative TBCs (GZO-YPSZ and YAG) potentially able to withstand the CMAS attack and erosive environments, respectively, has been carried out.No clear evidence of a different behaviour of TBC has been observed, at least in the considered aging time and temperature range.     

A facile pathway to prepare molybdenum boride powder from molybdenum and boron carbide

Molybdenum boride is an ideal hard and wear-resistant material. In this study, a new method is proposed for preparing molybdenum boride, by which Mo first reacts with B₄C to generate the mixture of molybdenum boride and C, and then the product is decarburized by molten Ca to generate CaC₂. Pure molybdenum boride could be obtained after acid leaching to remove the by-product CaC₂. According to the experimental and thermodynamic calculation results, it is concluded that the single-phase MoB could be successfully prepared, while Mo₂B, Mo₂B₅, and MoB₄ could not be synthesized by this method. Moreover, it was found that the particle size of finally prepared MoB is determined by particle size of raw Mo powder. The residual carbon content of the product could be decreased to 0.10 wt% after first reaction at 1673 K for 6 hours and then decarburization reaction at 1673 K for 6 hours.     

具有光照鲁棒的图像匹配方法

针对现有的基于局部特征的图像匹配算法对光照变化敏感、匹配正确率低等问题，提出一种具有光照鲁棒性的图像匹配算法。首先使用实时对比保留去色（RTCP）算法灰度化图像，然后利用对比拉伸函数模拟不同光照变换对图像的影响从而提取抗光照变换特征点，最后采用局部强度顺序模式建立特征点描述符，根据待匹配图像局部特征点描述符的欧氏距离判断是否为成对匹配点。在公开数据集上，所提算法与尺度不变特征变换（SIFT）算法、加速鲁棒特征（SURF）算法、"风"（KAZE）算法和ORB算法在匹配速度和匹配正确率上进行了对比实验。实验结果表明：随着图像亮度差异的增加，SIFT算法、SURF算法、"风"（KAZE）算法和ORB算法匹配正确率下降迅速，所提算法下降缓慢并且正确率均高于80%；所提算法特征点检测较慢和描述符维数较高，平均耗时为23.47 s，匹配速度不及另外四种算法，但匹配质量却远超过它们。对实时性要求不高的系统中，所提算法可以克服光照变化对图像匹配造成的影响。     

基于3D打印技术复制砂浆节理的剪切试验及峰值抗剪强度模型

为进一步研究节理三维形貌特征与节理峰值抗剪强度的关系,首先采用巴西劈裂试验获取了自然劈裂岩石表面,通过三维扫描技术获取了节理面形态的高精度点云,通过逆向建模得到了自然岩石表面的立体模型,结合3D打印技术制作出了与自然岩石表面一致的PLA模具,以3D打印获得的底模通过水泥砂浆浇筑了含有自然结构面形貌的相似节理面试样。PLA模具与复制材料差异较大,复制材料在凝结过程中不易与PLA模具黏结,进而使脱模过程较为方便,不会破坏节理面。同时PLA模具可重复进行相似材料复制工作,具有可重复使用的优点。然后进行了具有5组形貌面的20个水泥砂浆节理面在4种不同法向荷载情况下的结构面剪切试验,得到了结构面剪切位移-荷载曲线。研究了结构面峰值抗剪强度、峰值位移、剪切刚度影响因素。节理经过剪切后形貌面出现不同程度的磨损,其磨损范围与等效高差分布范围基本一致,并且在等效高差为剪断破坏模式且成片的区域磨损较为严重。在新粗糙度指标基础上提出了新的峰值抗剪强度模型,经试验对比显示出新模型的有效性。在新模型基础上提出了一个简化模型。对比发现新模型简化后其计算精度较新模型有所降低但由于所需参数减小计算较为方便,新模型简化结果精度虽然有所下降但是还是比Barton公式精度高。     

简体接管边缘应力区局部减薄处应力特征

参考《压力容器定期检验规则》第40条,采用有限元方法计算了筒体接管边缘应力区局部减薄处的应力分布,得到了局部减薄处凹坑的尺寸与位置对应力的影响趋势,讨论了应力集中系数随尺寸变化的规律,为筒体接管边缘应力区局部减薄处的强度评定提供了一定的计算依据。     

聚乙烯催化剂表面分形和多重分形特征

应用分形和多重分形理论研究了负载型聚乙烯催化剂(简称催化剂)表面形态。提出一种图片处理和计算过程更加完备的基于扫描电子显微镜照片的分形维数和多重分形谱计算程序,对4种催化剂进行分析计算。探讨了分形维数、多重分形谱相关参数与催化剂表面形态及与聚合活性的对应关系。实验结果表明,催化剂表面形态的复杂程度可以用表面分形维数来表征,聚合活性高的催化剂表面形态更加复杂,有更大的比表面积,对应的分形维数值也越大。催化剂表面分形维数的变化程度可以用多重分形谱来表征,聚合活性高的催化剂表面分形维数的跨度和分散程度更高。提出的分形维数和多重分形谱计算程序为催化剂的评定与设计提供了一种实用的手段。     

移动机器人路径规划方法研究

移动机器人技术研究中的一个重要领域是路径规划技术，它分为基于模型的环境已知的全局路径规划和基于传感器的环境未知的局部路径规划。综述了移动机器人路径规划技术的发展现状指出了各种方法的优点与不足，最后对移动机器人路径规划技术的发展趋势进行了展望。     

CHAOTIC HYDRODYNAMICS IN HORIZONTAL GAS-LIQUID BUBBLY FLOW

ＮＯＭＥＮＣＬＡＴＵＲＥｄ———ｅｍｂｅｄｄｉｎｇｄｉｍｅｎｓｉｏｎ ,ｄｉｍｅｎｓｉｏｎｌｅｓｓＣｄ(ｒ)———ｃｏｒｒｅｌａｔｉｏｎｓｕｍ ,ｄｉｍｅｎｓｉｏｎｌｅｓｓＮ———ｎｕｍｂｅｒｏｆｐａｉｒｓｏｆｐｏｉｎｔｓｏｎｔｈｅｒｅｃｏｎ ｓｔｒｕｃｔｅｄａｔｔｒａｃｔｏｒ,ｄｉｍｅｎｓｉｏｎｌｅｓｓｒ———ｓｃａｌｉｎｇｄｉｓｔａｎｃｅ ,ｄｉｍｅｎｓｉｏｎｌｅｓｓＤｃ ———ｃｏｒｒｅｌａｔｉｏｎｄｉｍｅｎｓｉｏｎ ,ｄｉｍｅｎｓｉｏｎｌｅｓｓＫ———Ｋｏｌｍｏｇｏｒｏｖｅｎｔｒｏｐｙ ,ｂｉｔｓ/ｓＲ…     

隔河岩水电厂现地控制单元改造

结合隔河岩水电厂现地控制单元改造工程项目，依据多年的计算机监控 系统研制开发经验，对计算机监控系统现地控制单元的结构特点、技术路线及实现方法等进 行了探讨。